Skip to main content

Troubleshooting, Checklist, And Solution Of Positive Displacement Pump.

Troubleshooting, Checklist, And Solution Of Positive Displacement Pump.


 



Like other Positive Displacement Pumps or reciprocating machines, a reciprocating pump requires proper attention to the inspection checklist, monitoring, troubleshooting, solution, and maintenance for smooth operation. Troubleshooters should have to inspect as well as monitor the whole pumps sincerely. Periodical inspection Troubleshooting, Checklist, And Solution Of Reciprocating Pump may increase the lifetime. Periodical Troubleshooting, Checklist, And Solution Of Reciprocating Pump may decrease intercepted production and also increase productivity.

Many problems may crop up during startup, and running times, so one needs to know about a reciprocating pump & Troubleshooting. Possible reciprocating pump and troubleshooting and their probable remedies are disguised below:

 

01. Low Capacity:

Possible Causes:

  • The speed is too low.

  • Liquid end valves leaking.

  • The piston ring or liner is worn.

  • Undersized Plungers.

Remedy Or Action:

  • Increase speed.

  • Re-lap or replace the valve.

  • Replace worn parts.

  • Install the correct size.

 

02. Excessive Wear:

Possible Causes:

  • Misalignment.

  • Bent position/ rod/ plunger.

  • Worn bore.

Remedy Or Action:

  • Check alignment.

  • Check for straightness.

  • Replace the liner or Rebore.

 

03. Overheating:

Possible Causes:

  • Stuffing box overheating.

  • Bearing overheating.

  • Fluid is too viscous.

Remedy Or Action:

  • Check that packing is not too tightened or badly fitted.

  • Check packing lubricant.

  • Review the specification of the Pump.

  • Check oil level or lubricant condition.

  • Correct the bearing for misalignment or excessive tightness.

  • Check the fitting and condition of the oil seals.

  • Reduce fluid viscosity.

 

04. Pumps Requires Excessive Power:

Possible Causes:

  • Pumps speed or RPM too high.

  • Misalignment of pumps.

  • Internal friction.

  • Tight bearings.

  • Lack of lubrication.

Remedy Or Action:

  • Correct against the recommendation speed.

  • Check the alignment of the pump and Driver, also Foundations.

  • Repair the rubbing contact, clogging, etc.

  • Check bearing and packings.

  • Check the quantity and quality of lubricant.

 

05. Vibration And Noise.

Possible Causes:

  • Cavitation.

  • Misalignment.

  • Bent shaft,

  • Faulty Bearings.

  • Excessive fluid viscosity.

  • Improper pump assembly.

Remedy Or Action:

  • Check pump operating conditions.

  • Correct alignment with the driver.

  • Check and replace if necessary.

  • Correct or review product suitability.

  • Check and rectify.

 

06. Short Packing Life:

Possible Causes:

  • Incorrect packing

  • Misalignment of a plunger or piston rod with a stuffing box.

  • Worn plunger or piston rod.

  • Worn stuffing box bore.

  • The packing gland is too tight.

  • Too much packing in the box.

  • Abrasive in pumpage.

  • Inadequate packing lubricant.

Remedy Or Action:

  • Install correct packing.

  • Improve alignment.

  • Replace worn parts.

  • Repair or replace the stuffing box.

  • Lossen gland packing.

  • Reduce the number of rings.

  • Strains or filters in late.

  • Improve lubrication.

 

07. No Discharge:

Possible Causes:

  • Cavitation.

  • The speed is too low.

  • Not Primed.

  • Excessive suction lift.

  • Air Leaks.

Remedy Or Action:

  • Check Priming.

  • Increase speed.

  • Reduce suction lift.

  • Check the system and eliminate air leaks by sealing etc.

 

PLEASE READ MORE.....

  1. Industrial Catalyst And Classification.
  2. Electrical Hazards And Precautions.
  3. Renewable, Sustainable, Clean, or Green Energy.
  4. What Is Renewable Energy Or Renewable Resources, Or Clean Energy?
  5. Standard Operating Procedure (SOPs) Of The Steam Turbine.
  6. What Is Vacuum Hazard?Power Plant And Types Of Power Plants.
  7. Electrical Wiring Or Cabling। Classifications Of Electrical Wiring।

Power Plant And Types Of Power Plants.

  1. Steam Boiler। Mountings And Accessories Of Boiler.
  2. Standard Operating Procedure (SOP) Of The Steam Turbine.
  3. Metals। Used, Properties, Classification, And Types Of Metals.
  4. The Best Way To Search, Emergency Escape, And Rescue Operations From Accidents.
  5. What Is Distillation Process? Kinds Of Distillation Process.
  6. What Is Electrical Measuring Instrument And Testing Equipments.
  7. The Blessing Of Science In Modern Civilization Is The AC Motor Or DC Motor.
  8. The Mechanical Power Transmission System Or Energy Transfer.
  9. Troubleshooting, Checklist, And Solution Of Positive Displacement Pump.
  10. What is Packed Tower, Packing Elements, Function Of Packing Elements?
  11. Housekeeping Promotes Occupational Safety, Industrial Safety, or Workplace Safety.
  12. Industrial Static Vessels And Towers.
  13. How To Use Natural Gas In Petrochemical Plant.
  14. Question With Answer About Turbine Or Compressor Lube Oil Systems.
  15. Question With Answer About Turbine And Compressor In Process Industries 02.
  16. Question With Answer About Turbine And Compressor In Process Plant 01.
  17. What Is Compressor And Compression System? Working Principal Of Compressor.
  18. Sewage Or Wastewater Treatment Process.
  19. Explosion Hazard And How To Prevent It?
  20. How To Prevent Fire Hazards In The Workplace?
  21. Accident And Its Prevention In Work Place.
  22. Occupational Safety And Safety Requirements In Industries.
  23. Different Type Of Boiler. Boiler Operation And Operation Coefficient.
  24. Pump Cavitation And Prevention.
  25. Pumps & How It Works?
  26. Centrifugal Pump Checklist, Troubleshooting And Solution.
  27. What Is Seal And Types Of Seal?
  28. Safety Measures Associated With Confined Space.
  29. Why Static Charge Is Dangerous In Industrial Or Manufacturing Industries.
  30. What About Cooling Tower? Types Of Cooling Tower.
  31. What Is Gas Hydrate.How To Prevent It?
  32. Personal Protective Equipment (PPE). Types Of PPE.
  33. What Is Filter Or Separator? Types Of Filters.
  34. What Is Strainer? Types of strainer.
  35. What Is Lubricant And Properties Of Lubricant?
  36. The Steam Turbine, Classification Of Steam Turbine And How It Works?
  37. Personal Protective Equipment (PPE). Types Of PPE.
  38. What Is Filter? Types Of Filters.
  39. What Is Rupture Disc, How It Work?
  40. Let's know about general pipe fittings commonly needed in the industry.
  41. What Is Steam Traps?
  42. What is Fire Point, Smoke Point, Freezing Point, Dew Point, Flash Point, Pour Point, Boiling Point, Bubble Point?
  43. What is Critical Point,Surge point,Yield point,Aniline point,Triple Point,Melting Point,Auto ignition Point?
  44. Types Of Control Valve.
  45. Bearing And Different Types Of Bearing.
  46. What Means Process, Process Symbol, Process Diagram?
  47. About Heat Exchanger.
  48. Difference between Pressure Safety Valve and Pressure Relief Valve.
  49. About Check Valve.
  50. Why SHIPHON TUBE Is Used On Steam Pipeline?
  51. What Is Conservation Vent Valve?
  52. Different Types of valves.
  53. General Checklist List for Pre-start and Starting up the Centrifugal Pumps.
  54. Liquefaction Process Technologies for LNG Production.
  55. What Is Hydrostatic Test.
  56. What Is Deaeration Process? How To Remove O2, From Boiler Feed Water?
  57. Pumps Operation in Series and Parallel.
  58. Why Need To Maintain In Process Steam Quality.
  59. Why we need to close the(discharge) isolation valve of a centrifugal pump during start up.
  60. What Is A Steam Turbine.
  61. STEAM EJECTOR WORKING PRINCIPL.
  62. Glycol Dehydration Basic Process.
  63. Why Needs Tank blanketing In Process Plant.
  64. Let's Know About Industrial Storage Tanks.
  65. What Is Gas Hydrate. How To Create It On Pipeline And How To Prevent It?
  66. What Is Pumps " NPSHr “ Net Positive Suction Head?
  67. What Is Methanol – CH3OH?
  68. How does a liquid ring vacuum pump work.
  69. Difference between LNG, LPG and NGL.
  70. What About Cooling Tower? Types Of Cooling Tower.
  71. What Is Conservation Vent Valve.
  72. Why do we use deaerators In Process Plant?
  73. General Checklist List the Essential Steps and precautions for Pre start and Starting up the Centrifugal Pumps.
  74. How To H2 Production In Process Plant.
  75. Why Static Charge Is Dangerous In Industrial Or Manufacturing Industries.

Comments

Popular posts from this blog

General Checklist List for Pre-start and Starting up the Centrifugal Pumps.

General Checklist the Essential Steps and precautions for Pre-start and Starting up the Centrifugal Pumps . # What’s the things you Should be attention physically? # General centrifugal pump start up procedure:- Before pump start-up you must perform these tasks:- *01.  Open the suction valve , do priming by venting all the air inside the suction line by opening any vent or even the PG vent till liquid coming out then close , now you confirm no air inside the system to reduce the chances of pump getting cavitation *02.   Open any re-circulation  or cooling lines. *03.   Fully close or partially open the discharge valve, depending on system conditions. *04.   Start the driver. *05.   Slowly open the discharge valve until the pump reaches the desired flow. *06.   Check the pressure gauge to ensure that the pump quickly reaches the correct discharge pressure. *07.   If the pump fail to reach the correct pre...

Different Types of valves

Different Types of valves Different Types of valves uses in different sectors. 1.  Globe valve:- 2.  Gate valve:- 3.  Ball valve:- 4.  Butterfly valve:- 5.  Diaphragm valve:- 6.  Plug valve:- 7.  Needle valve:- 8.  Angle valve:- 9.  Pinch valve:- 10.  Slide valve:- 11.  Flush bottom valve:-   12.  Solenoid valve:- 13.  Control Valve:- 14.  Flow regulating valve:- 15.  Back pressure regulating valve:- 16.  Y-type valve:- 17.  Piston valve:- 18.  Pressure regulating valve:- 19.  Check valve:- PLEASE READ MORE..... Industrial Catalyst And Classification. Electrical Hazards And Precautions. Renewable, Sustainable, Clean, or Green Energy. What Is Renewable Energy Or Renewable Resources, Or Clean Energy? Standard Operating Procedure (SOPs) Of The Steam Turbine. What Is Vacuum Hazard? Power Plant And Types Of Power Plants...

What is Fire Point, Smoke Point, Freezing Point, Dew Point, Flash Point, Pour Point, Boiling Point, Bubble Point?

# Fire Point :-  The lowest temperature at which the vapor of that fuel will continue to burn for at least 5 seconds after ignition by an open flame. #Smoke Point:-   The temperature at which, under specific and defined conditions, an oil begins to produce a continuous bluish smoke that becomes clearly visible. #Freezing Point:-  The temperature at which water changes phase from a liquid to a solid. # Dew Point:-   T he temperature at which air is saturated with water vapor. # Flash Point:-  T he lowest temperature at which enough fluid can  evaporate to form a combustible concentration of gas. #Pour Point:- The lowest temperature at which the oil will pour or flow when it is cooled without stirring. #Boiling Point:-   The temperature at which the vapor pressure of a liquid is equal to the pressure of the atmosphere on the liquid. #Bubble Point:-   The temperature wh...

Industrial Catalyst And Classification.

Principle Of Industrial Catalyst And Classification Of Catalyst.   Principle Of Industrial Catalyst : An industrial catalyst is a substance that accelerates a chemical reaction without undergoing any significant change in its own chemical composition. Catalysts work by lowering the activation energy required for the reaction to occur, thereby increasing the reaction rate. They provide an alternative pathway for the reaction to take place, which requires less energy and allows the reaction to proceed at milder conditions such as lower temperatures and pressures. Industrial catalysts are used in a wide range of chemical processes, including petrochemicals, refining, polymerization, and environmental applications. Classification Of Industrial Catalyst : Industrial catalysts can be classified into four main groups: 01. Homogeneous catalysts. Homogeneous catalysts are soluble in the reaction medium and are used mainly in the production of fine chemicals and pharmaceuticals. 02. Heteroge...

Difference between LNG, LPG and NGL

✅ LNG — Liquefied Natural Gas, is gas that has been Liquified at very low temp. and is transported as a liquid. It’s Primarily methane ,NG is a mixture of HC which, when liquefied, form a clear colorless,odorless liquid; it’s usually transported and stored at a temp. very close to its boiling point at atmospheric pressure (~ -160), The actual composition of LNG will vary depending on its source and on the liquefaction process, but in all cases the major is methane with small percentages of the heavier HC such as ethane, propane, butane and pentane ,N2 may be present.  ✅ LPG — Liquefied Petroleum Gas gas that is liquid near room temperature and at some extent of pressure. This product has very little methane and butane and is primarily propane (C3),LPG is more dense (has a higher specific gravity) than natural gas ,Their common characteristic is that they can be compressed into liquid at relatively low pressures ,The two most common LPG constitutes are Propane and Butan...