Skip to main content

The Steam Turbine, Classification Of Steam Turbine And How It Works?


steam turbine.https://techproces.com/
Steam Turbine.https://techproces.com/

The turbine is a mechanical device or mechanical mechanism that converts thermal energy to mechanical/kinetic energy. In Petrochemicals, Chemicals, Power Generation, Ammonia, Oil and Gas, Manufacturing Industries, the steam turbine is used as the driving system or driver. Such as a steam turbine used to drive a  power generator in the power plant.

# Purposes Of Steam Turbine:

01. In industry, the steam turbine is used as the driving system or driver. Its drive Compressor, Pump, Blower, Fan, Generator, etc. 

02. The steam turbine is used to generating electricity at a power plant.

Labels:

Comments

Post a Comment

Popular Post.

General Checklist List for Pre-start and Starting up the Centrifugal Pumps.

General Checklist the Essential Steps and precautions for Pre-start and Starting up the Centrifugal Pumps . # What’s the things you Should be attention physically? # General centrifugal pump start up procedure:- Before pump start-up you must perform these tasks:- *01.  Open the suction valve , do priming by venting all the air inside the suction line by opening any vent or even the PG vent till liquid coming out then close , now you confirm no air inside the system to reduce the chances of pump getting cavitation *02.   Open any re-circulation  or cooling lines. *03.   Fully close or partially open the discharge valve, depending on system conditions. *04.   Start the driver. *05.   Slowly open the discharge valve until the pump reaches the desired flow. *06.   Check the pressure gauge to ensure that the pump quickly reaches the correct discharge pressure. *07.   If the pump fail to reach the correct pre...
Post a Comment
Read more

Different Types of valves

Different Types of valves Different Types of valves uses in different sectors. 1.  Globe valve:- 2.  Gate valve:- 3.  Ball valve:- 4.  Butterfly valve:- 5.  Diaphragm valve:- 6.  Plug valve:- 7.  Needle valve:- 8.  Angle valve:- 9.  Pinch valve:- 10.  Slide valve:- 11.  Flush bottom valve:-   12.  Solenoid valve:- 13.  Control Valve:- 14.  Flow regulating valve:- 15.  Back pressure regulating valve:- 16.  Y-type valve:- 17.  Piston valve:- 18.  Pressure regulating valve:- 19.  Check valve:- PLEASE READ MORE..... Industrial Catalyst And Classification. Electrical Hazards And Precautions. Renewable, Sustainable, Clean, or Green Energy. What Is Renewable Energy Or Renewable Resources, Or Clean Energy? Standard Operating Procedure (SOPs) Of The Steam Turbine. What Is Vacuum Hazard? Power Plant And Types Of Power Plants...
Post a Comment
Read more

What is Fire Point, Smoke Point, Freezing Point, Dew Point, Flash Point, Pour Point, Boiling Point, Bubble Point?

# Fire Point :-  The lowest temperature at which the vapor of that fuel will continue to burn for at least 5 seconds after ignition by an open flame. #Smoke Point:-   The temperature at which, under specific and defined conditions, an oil begins to produce a continuous bluish smoke that becomes clearly visible. #Freezing Point:-  The temperature at which water changes phase from a liquid to a solid. # Dew Point:-   T he temperature at which air is saturated with water vapor. # Flash Point:-  T he lowest temperature at which enough fluid can  evaporate to form a combustible concentration of gas. #Pour Point:- The lowest temperature at which the oil will pour or flow when it is cooled without stirring. #Boiling Point:-   The temperature at which the vapor pressure of a liquid is equal to the pressure of the atmosphere on the liquid. #Bubble Point:-   The temperature wh...
Post a Comment
Read more

Industrial Catalyst And Classification.

Principle Of Industrial Catalyst And Classification Of Catalyst.   Principle Of Industrial Catalyst : An industrial catalyst is a substance that accelerates a chemical reaction without undergoing any significant change in its own chemical composition. Catalysts work by lowering the activation energy required for the reaction to occur, thereby increasing the reaction rate. They provide an alternative pathway for the reaction to take place, which requires less energy and allows the reaction to proceed at milder conditions such as lower temperatures and pressures. Industrial catalysts are used in a wide range of chemical processes, including petrochemicals, refining, polymerization, and environmental applications. Classification Of Industrial Catalyst : Industrial catalysts can be classified into four main groups: 01. Homogeneous catalysts. Homogeneous catalysts are soluble in the reaction medium and are used mainly in the production of fine chemicals and pharmaceuticals. 02. Heteroge...
Post a Comment
Read more

Difference between LNG, LPG and NGL

✅ LNG — Liquefied Natural Gas, is gas that has been Liquified at very low temp. and is transported as a liquid. It’s Primarily methane ,NG is a mixture of HC which, when liquefied, form a clear colorless,odorless liquid; it’s usually transported and stored at a temp. very close to its boiling point at atmospheric pressure (~ -160), The actual composition of LNG will vary depending on its source and on the liquefaction process, but in all cases the major is methane with small percentages of the heavier HC such as ethane, propane, butane and pentane ,N2 may be present.  ✅ LPG — Liquefied Petroleum Gas gas that is liquid near room temperature and at some extent of pressure. This product has very little methane and butane and is primarily propane (C3),LPG is more dense (has a higher specific gravity) than natural gas ,Their common characteristic is that they can be compressed into liquid at relatively low pressures ,The two most common LPG constitutes are Propane and Butan...
Post a Comment
Read more